TECO N3 Instruction Manual - Free download as PDF File (.pdf), Text File (.txt) or read online for free. Manual inversor TECO 7300 N3. PRO 2500 Rack Mountable PowerCenter with Clean Power Stage 2 - read user manual online or download in PDF format. Pages in total: 24.

Are you looking for the the instruction manual of the KEF X300A? View the user manual of this product directly and completely free.
View online Specifications for Elan D1200 Amplifier or simply click Download button to examine the Elan D1200 guidelines offline on your desktop or laptop computer.

Back-UPS Pro ®

350 / 500

Lineage 2 interlude. User’s Manual

990-2052B Revision 3 5/99

&KHFN WKH %XLOGLQJ

:LULQJ )DXOW LQGLFDWRU

If the Building Wiring Fault indicator on the power plug stays lit, one of the following conditions exist:

∙Open or high resistance ground.

∙Hot and neutral polarity reversal.

∙Overloaded neutral circuit.

A lit indicator means that a possible shock hazard exists. Improper building wiring should be corrected by a qualified electrician.

Note: Improper building wiring will not prevent the UPS from operating, but will limit its protection capability. Improper building wiring could result in equipment damage that is not covered by APC. Please refer to APC’s Equipment Protection Policy for details.

6ZLWFK 2Q 7HVW WKH 836

Press the On/Test button.

You will observe the following events after pressing and releasing the On/Test button:

∙The green On Line indicator will flash.

∙The yellow On Battery indicator will light while a battery test is performed.

∙When the self test has successfully completed, only the green On Line indicator will be lit.

∙The red Overload indicator may flash briefly when the UPS is switched on.

Following the test, if a red indicator is lit or you want to perform a self test, consult the troubleshooting section.

6HWXS

&RQQHFW EDWWHU ZLUH

The UPS is shipped with one battery wire disconnected - in compliance with Department of Transportation (DOT) regulations. Connect the battery wire as shown.

The UPS will not operate unless the steps below are performed.

a. Set the UPS at the edge	b. Slide the battery	c. Grasp the tab attached to the
of a table.	compartment cover down.	battery and slide the battery
partially out. Connect the black
wire to the battery by pushing it all
the way onto the terminal. Small
sparks are normal.

d. Slide the battery back in.	e. Slide the battery compartment
Avoid pinching the wires.	cover back into place.

&RQQHFW HTXLSPHQW WR

836

Do not plug surge protectors or power strips into Battery Backup outlets.

Battery Backup Plus Surge Protection outlets (4)

Data sensitive equipment such as a computer, monitor, and external drives should be powered by these outlets. Battery power is automatically provided in case of power outage. Power (utility or battery) is not supplied to these outlets when the UPS is switched Off.

Surge Protection outlets (3)

Equipment such as a printer, fax machine, scanner, or even a desk lamp should be powered by these outlets. These outlets do not provide power during a power outage. These outlets are always on (when utility power is available) and are not controlled by the front panel switches.

Transformer Block outlets (2)

One Battery Backup Plus Surge Protection and one Surge Protection outlet accept transformer blocks.

&RQQHFW 86% FDEOH DQG

LQVWDOO VRIWZDUH

RSWLRQDO SURFHGXUH

Your computer system must be On before starting this procedure. Have your Windows 98 operating system CD ready.

Connect the USB cable end, with USB symbol facing down, to the UPS. Connect the other USB cable end directly to an available USB port on your computer.

USB connection on rear panel of UPS:

Monitor

Fax

Computer

Printer

Scanner

External

Drive

Typical Installation

Black Velcro Cord Straps (2 - not shown)

Straps can be used to manage cords.

1.After connecting the USB cable, the Windows 98 'ADD NEW HARDWARE WIZARD' dialog box is displayed. Insert your Windows 98 operating system CD into the computer’s CD-ROM drive before proceeding.

2.Follow the installation instructions on your computer screen.

During installation, Windows will need to search for new drivers. When prompted, make sure the CD-ROM drive box is checked.

3.After installation is complete, a 'Windows 98 CD-ROM' dialog box may appear. If this happens, just close the box.

4.Remove the Windows 98 Operating System CD from the CD-ROM drive.

5.Insert the APC Power Management Extensions for Windows 98 CD into the computer’s CD-ROM drive.

The software user guide is a file on the CD. Its filename is User’s Guide.pdf.

3ODFH 3RZHU 836

Power Pro Quipp 300a Manual

Place the UPS to avoid:

∙Direct sunlight.

∙Excessive heat.

∙Excessive humidity or contact with liquids.

Plug the UPS directly into a wall outlet.

∙The Building Wiring Fault indicator may flash momentarily while being plugged in.

∙The UPS begins charging when connected to utility power.

∙Four hours of charging should be sufficient to achieve maximum battery capacity.

Power Pro Quipp 300a Instructions

&RQQHFW SKRQH FDEOHV WR

VXUJH SURWHFWLRQ

The UPS can protect up to two telephone lines on one phone cable. Connect your modem/fax/phone as shown with the release tab facing up for the ends connected to the UPS.

Wall

Outlet

Modem/Fax/Phone

6.Follow the installation instructions on your computer screen.

If the software does not automatically install, your Windows 98 auto run feature may have been disabled.

To install:

a.Click “ Start”.

b.Click “ Run”.

c.Enter the path to the setup.exe file on the CD-ROM drive:

CD-ROM drive letter:/setup.exe

Quipp Power Pro 300a Manual

d.Click “OK”.

7.After installation is complete, the APC plug Task Bar icon will appear on your Task Bar (near the clock). To start the Power Management application Double-click on the APC plug Task Bar icon or start the Power Management applet in the Windows 98 control panel.

There are four indicator lights and a speaker grille on the front panel to indicate UPS status. Download autoenginuity scan tool torrent.